湖北快3走势图

咨询热线:

0531-88771136

您的当前位置: 湖北快3走势图 > 湖北快3走势图 > 正文

模具制作过程中必须规则都有哪些?

来源:http://www.ok9868.com     发布时间:2019-12-19 16:06:11    点击:

山东模具的制作装配都有哪些线规范
  What are the production and assembly line specifications of Shandong mould
  模具装配线后,应遵循以下关键规范:
  After the die assembly line, the following key specifications shall be followed:
  (1) 标准件的装配线应可靠。连接铁件时,锚定螺栓外螺纹的长度不应小于锚定螺栓的直径,连接铸造件时,不应小于锚定螺栓直径的1.5倍;销与各部位的相互配合长度应大于销直径的1.5倍;地脚螺栓和销的内孔不得露出上下模座及其它部位的表面。
  (1) the assembly line of standard parts shall be reliable. When connecting the iron parts, the length of the external thread of the anchor bolt shall not be less than the diameter of the anchor bolt; when connecting the casting parts, it shall not be less than 1.5 times of the diameter of the anchor bolt; the mutual matching length of the pin and each part shall be greater than 1.5 times of the diameter of the pin; the internal hole of the anchor bolt and pin shall not expose the surface of the upper and lower mold bases and other parts.
  (2)挖掘出料孔或进料槽,以确保生产或废物随意排放。
  (2) excavate the discharge hole or feed chute to ensure the production or waste is discharged at will.
  (3) 标准件也应更换。拧紧螺钉与精密定位销孔的相互配合应正常、良好。
  (3) Standard parts shall also be replaced. The mutual fit between the screw and the precise locating pin hole shall be normal and good.
  (4) 磨具在压力机上的安装规范应符合机械设备的使用规则,起重件应可靠。
  (4) the installation specification of grinding tools on the press shall conform to the use rules of mechanical equipment, and the lifting parts shall be reliable.
  (5) 磨料应按生产和生产规范进行试验,突破性生产应符合设计方案规定。
  (5) Abrasives shall be tested according to production and production specifications, and breakthrough production shall meet the requirements of design scheme.
  (6) 模架精度应符合国家行业规范(LF/t8050-1998{五金模架技术规范,LF/t8071-1997五金模架精度检验)的要求。五金模具闭合高宽比应符合工程图纸要求。
山东模具
  (6) the accuracy of the mold base shall meet the requirements of the national industry specifications (LF / t8050-1998 {technical specifications for metal mold base, LF / t8071-1997 precision inspection for metal mold base). The ratio of height to width of the closed metal mold shall meet the requirements of the engineering drawing.
  (7) 对于装配线的五金模具,下模应沿定位销上下拉起,拉起应平稳可靠。
  (7) for the hardware mold of the assembly line, the lower mold shall be pulled up and down along the locating pin, and the pulling shall be stable and reliable.
  (8) 模和模之间的空间应符合工程图纸要求的规则,并应均匀。模具座或型腔的工作行程组织符合技术规范要求。
  (8) the space between the mold and the mold shall conform to the rules required by the engineering drawing and shall be uniform. The working stroke organization of die base or cavity meets the requirements of technical specifications.
  (9) 挡料设备的精确定位及相关部位应符合工程图纸规定。冷冲压模具导板之间的距离应与工程图纸的要求相同,导向面应平行于模具的进给方向,导向板采用侧压设备,其侧压板应灵活可靠。
  (9) the accurate positioning and relevant parts of the retaining equipment shall meet the requirements of the engineering drawings. The distance between the guide plates of the cold stamping die shall be the same as the requirements of the engineering drawing. The guide surface shall be parallel to the feed direction of the die. The guide plate shall be side pressing equipment, and its side pressing plate shall be flexible and reliable.
  (12) 倾倒和顶升设备的相关部件应符合设计方案的规定。超宽应在允许要求的规划范围内。掘进工作面不得有歪斜或单边歪斜,以保证生产或废料能立即排出,满足注水要求。
  (12) relevant parts of dumping and jacking equipment shall meet the requirements of design scheme. The over width shall be within the allowed planning range. There shall be no skew or unilateral skew in the driving face to ensure that production or waste can be discharged immediately and meet the water injection requirements.
  以上就是对山东模具的制作装配都有哪些线规范的介绍,想要了解更多,欢迎访问官网http://www.ok9868.com
  The above is an introduction to the production and assembly line specifications of Shandong mold. To learn more, please visit the official website http://www.ok9868.com
联系我们 contact

山东济南模具_铝合金压铸厂-济南宏捷模具湖北快3走势图

电话1:13173017488

电话2:18615459955

传真:0531-88771136

邮箱:hlm369@126。com

地址:山东省济南市大桥镇大王村北跨商务中心后三层白楼

山东济南模具_铝合金压铸厂-济南宏捷模具湖北快3走势图 手机: 13173017488 咨询热线: 0531-88771136 咨询热线:18615459955 邮箱:hlm369@126.com

公司地址: 山东省济南市大桥镇大王村北跨商务中心后三层白楼

湖北快三走势图 爱波彩票APP下载 湖北快3走势图 安徽快3开奖结果 湖北快3走势图 安徽快3开奖结果 博悦彩票平台 爱尚彩票APP下载 博盛彩票APP下载 湖北快3走势图